為什么在采購濟南樓承板前要了解一些相關知識，因?yàn)槭袌?chǎng)上樓承板的種類、型號等層次不一，一不小心就可能會步入陷阱，所以要了解相關的知識，這樣更好的完成采購。

Why do you need to know some relevant knowledge before purchasing Jinan floor bearing plates? Because the types and models of floor bearing plates in the market are different, you may fall into a trap if you are not careful, so you need to know relevant knowledge to complete the purchase better.

1、如何選擇板型的波高

1. How to select wave height of plate type

要看整個樓承板的厚度來考慮選擇是用75波高系列的還是51波高系列的，有40系列，46系列，60系列，65波高系列。一般來說波高越低，承載力就越低，然后就是波峰間距越大，承載力就越小，如果整個樓板厚度在10公分以?xún)?nèi)，好選用選用波高40系列，整個樓板厚度在10-13公分以?xún)?nèi)，好選用50波高系列，在13公分以上，好選用75系列。

Depending on the thickness of the whole floor bearing plate, you can choose 75 wave height series or 51 wave height series, including 40 series, 46 series, 60 series and 65 wave height series. Generally speaking, the lower the wave height is, the lower the bearing capacity will be. The larger the wave crest spacing is, the smaller the bearing capacity will be. If the thickness of the entire floor is less than 10 cm, it is better to select the wave height 40 series. If the thickness of the entire floor is less than 10-13 cm, it is better to select the 50 wave height series. If the thickness of the entire floor is more than 13 cm, it is better to select the 75 series.

2、如何選擇樓承板的厚度

2. How to select the thickness of floor bearing plate

樓承板的厚度選擇，樓承板的厚度主要是看樓板的厚度和鋼結構次梁的間距，這個計算是很有技術含量的！他是根據樓承板的截面模量，截面慣性矩等計算出來的。

The thickness of the floor bearing plate is mainly determined by the thickness of the floor slab and the spacing between the secondary beams of the steel structure. This calculation is very technical! It is calculated according to the section modulus and section inertia moment of the floor bearing plate.

3、如何根據樓承板板型特點

3. How to According to the Characteristics of Floor Bearing Plate

樓承板主要分為開口樓承板，樓承板，鋼筋桁架樓承板。不管是哪種型號的樓承板，利用率越高，成本就越便宜，利用率=有效寬度/原材料進料寬度。但從美觀的角度來說，式樓承板好，施工完畢后該板型板底平整、腹板貼合，大約3-5mm的間隙，如果不做吊頂，可以直接噴漆可做成企口型天花板、也可披刮膩?zhàn)雍笸克⑺酝苛献龀善桨逄旎ò?、還可直接貼壁布或壁紙裝飾成彩色天花板；

Floor bearing plate is mainly divided into open floor bearing plate, floor bearing plate and steel bar truss floor bearing plate. No matter what type of floor bearing plate is, the higher the utilization rate is, the cheaper the cost is. The utilization rate=effective width/raw material feeding width. However, from the aesthetic point of view, the type floor bearing plate is good. After construction, the bottom of the plate is flat, the web is jointed, and the gap is about 3-5 mm. If there is no ceiling, it can be directly painted to make a tongue and groove ceiling, or painted with water-based paint after puttying to make a flat ceiling, or directly pasted with wallpaper or wallpaper to decorate a colorful ceiling;

如果做吊頂?shù)脑?huà)，不用打孔，不用膨脹螺絲固定，直接用兩片專用掛件掛在3-5mm的腹板貼合處，直接固定就可以?？s口式樓承板就比較次之?？礃I(yè)主或工程要求，會從美觀的角度還是經濟的角度上來考慮板型的選擇。

If the suspended ceiling is made, it is not necessary to drill holes or fix it with expansion screws. It can be directly fixed by hanging two pieces of special pendants at the 3-5mm web joint. The necked floor bearing plate takes the second place. Depending on the requirements of the owner or the project, the choice of plate type will be considered from an aesthetic or economic perspective.

采購樓承板要了解的三個方面在此就講解完畢了，您對此有怎樣的想法或者需求，都可以隨時來我們網站http://m.plisse.cn進行咨詢了解！

The three aspects you need to know about purchasing floor bearing plates are explained here. You can come to our website at any time for your ideas or needs http://m.plisse.cn Ask about it!