復合巖棉板的結構主要分為四層：膠粘劑層，隔熱層，涂片層，涂料層及相關輔料。粘合劑層在底層和表面層之間，并且上層和下層與膠凝材料牢固地結合在一起。復合巖棉板制作時需要注意4個問題，下面濟南巖棉板廠家為你解析。

The structure of composite rock wool board is mainly divided into four layers: adhesive layer, thermal insulation layer, smear layer, coating layer and related auxiliary materials. The adhesive layer is between the bottom layer and the surface layer, and the upper layer and the lower layer are firmly combined with the cementitious material. There are four problems that should be paid attention to when making composite rock wool board. The following is the analysis of Jinan rock wool board manufacturer.

<一>:根據生產工藝參數，規定了復合巖棉板出廠前的技術要求。復合巖棉板安裝后，復合巖棉板的外觀應達到相同的顏色卡號，復合巖棉板不應有色差缺陷。復合巖棉板的外部不應有明顯的沖擊或劃傷，是否缺少配套配件，面板、天花板、墊子、底槽等附件是否會到達。

<1> According to the production process parameters, the technical requirements for composite rock wool board before delivery are specified. After the composite rock wool board is installed, the appearance of the composite rock wool board shall reach the same color card number, and the composite rock wool board shall be free of color difference defects. There should be no obvious impact or scratch on the exterior of the composite rock wool board, whether there is a lack of supporting accessories, and whether the panel, ceiling, mat, bottom slot and other accessories will arrive.

<二>:復合巖棉板要經過質量檢查之前，進廠，并擁有產品，不符合質量檢測認可產品的證書在船上不允許安裝。建設工作都應該施工工具：卷尺，石筆，打箱，型材切割機，焊接工具，錘子，等準備好了。

<2> : The composite rock wool board shall enter the factory before quality inspection and have products. The certificate of unqualified products is not allowed to be installed on board. Construction tools should be prepared for construction: tape measure, stone pen, boxing, profile cutting machine, welding tools, hammer, etc.

<三>:焊工上崗。合格的焊工評估和采取行動之前達到三級資質。當電焊工上崗，就須佩戴特殊工種執照。工藝要求。根據現有技術的技術制造復合巖棉板需要預定的生產參數。安裝在同一色卡的復合巖棉板出現后應達到復合巖棉板不能有顏色缺陷。

<3> : Welders are on duty. Qualified welders shall be qualified to Level III before assessment and action. When electric welders are on duty, they must wear a special type of work license. Process requirements. The predetermined production parameters are required for manufacturing composite rock wool board according to the prior art. The composite rock wool board installed on the same color card shall be free of color defects after appearance.

<四>:如果損傷區域較大或劃痕長度大于必要的變化，則在復合巖棉板外側不應有明顯的沖擊或劃痕。門框上方隔倉復合巖棉板安裝工藝規范，下板為門框寬度相同的面板，跡線。一定沒有針跡。復合巖棉板安裝后，整個板的垂直度是板縫的平整度，復合巖棉板的頂平面度是板縫的平整度。天花板和頂部輪廓之間的間隙不大于。頂棚縫線應在同一直線上。

<4> : If the damage area is large or the scratch length is greater than the necessary change, there should be no obvious impact or scratch outside the composite rock wool board. The installation process specification for the partition composite rock wool board above the door frame is as follows: the lower plate is a panel with the same width as the door frame, with traces. There must be no stitch. After the composite rock wool board is installed, the perpendicularity of the whole board is the flatness of the board joint, and the top flatness of the composite rock wool board is the flatness of the board joint. The gap between the ceiling and the top profile is not greater than. The ceiling seam shall be in the same straight line.

復合巖棉板是巖棉板的一個延伸，復合巖棉板主要用于墻體保溫，屋頂保溫，門保溫和地板保溫，但重要的是墻體保溫的應用。你有需求就來我們網站http://m.plisse.cn咨詢了解吧！

Composite rock wool board is an extension of rock wool board. Composite rock wool board is mainly used for wall insulation, roof insulation, door insulation and floor insulation, but the most important is the application of wall insulation. Come to our website if you need http://m.plisse.cn Ask and understand!